Unit Heaters
Sizes: 12″ to 24″ (fan diameter)
Capacities: 1100 to 4500 CMF, 29,950-275,000 BTU/hr.
Standard: Adjustable louvers, steam, water coils, totally enclosed industrial motor with guard and heavy gauge casing.
Propeller Fans
Sizes: 8″ to 24″ (fan diameter)
Capacities: 500 to 4500 CMF
Pressures: To .5″ WG
Standard: Direct connected, chrome plated motorslide mount/guard.
Options: Wall shutters.
Type B
Vaneaxial Fans
Sizes: 15″ to 54″ (fan diameter)
Arrangement: 9, Belt driven
Capacities: 2500 to 65,000 CFM
Pressures: To 2.5″ WG
Accessories: Inlet bells and screens, suspension clips, shaft seals, mounted motor and drive, belt guard, support legs, and sparkproof wheel constuction.
Available: Steel and one piece cast aluminum wheels.
Type BL
Limit-Load
Ventilating Fans
Sizes: 245 to 1200 (fan diameters to 60″) SWSI
Arrangement: 1, 3 or 9
Capacities: To 100,000 CFM
Pressures: To full AMCA Class 2 ratings.
Standard: Belt or Direct Drive
Accessories: Door, drain, flanged outlet, shaft seal, type B or C sparkproof construction, split pillow block bearing(s), inlet screen, round or square flanged inlet, heat stinger, mounted motor, drive and guard.
Options: Unistrut motor rails (Arr. 1 unmounted).
Application: Clean air applications requiring AMCA Class 2 certification.
Volume Fans
Sizes: 8” to 21%’ (fan diameter)
Arrangements: 1 & 10 ’ Capacities: 100 to 4200 CFM
Capacities: 50 to 1800 CFM
Pressures: To 12” WG
Standard: Cast iron housing.
Options: Open steel wheels, flanged aluminum wheels, inlet and outlet flanges, drain, shaft seal, heat slinger, belt guard, motor and drive. Suitable for abrasive and corrosive applications.
Baby Vent Sets
Sizes: 33/4″ to 93/le” (fan diameter)
Capacities: 50 to 1800 CFM
Pressures: To 1.75″ WG ,fl Direct connected.
Accessories: Housing drain,
inlet/outlet screens, heat slinger.
Options: Aluminum or steel
wheels and fan cooled (TEFC) or
explosion proof (TEXP) motors.
Application: Low pressure intake or exhaust.
FRP Industrial Exhausters
Sizes: 17″-60″ (fan diameter)
Arrangement: 1
Capacities: To 30,000 CFM
Pressures: To 18″ WG
Standard: One piece, solid FRP
(fiberglass reinforced plastic) constructed wheels, impact resistant
housing.
Accessories: Drains, access door
and shaft seals.
Options: Wheels to handle
granular or fibrous materials or hot gases.
Application: Corrosive
gas handling problems.
Type E
Blowers Exhausters
Sizes: 71/2″ to 11′ (fan diameter)
Capacities: 60 to 565 CFM
Pressures: To 6″ WG
Standard: Cast iron housing (larger units); sheet metal housing (smaller units). Direct connected, 71/2′ diameter (2 VEH) supplied with variable speed drive and controller; other sizes with constand speed drives.
Options: Cast iron housing and motor base for small units. Fan cooled (TEFC) or explosion proof (TEXP) motors.
Applications: Low pressure, moderate air volume. Erosive or mildly corrosive gas handling.
Industrial Exhausters
Sizes: 12 1/4 to 56″ (fan diameter)
Capacities: 270 to 35, 750 CFM
Pressures: To 20″ WG
Accessories: Split pillow block bearings, type C spark resistant construction, housing access door, drain, flanged inlet and outlet, shaft seal, heat stinger, OSHA inlet screen, OSHA belt guard, unistrut motor rails, mounted motor and drive.
Options: Wheels designed Erto handle granular, fibrous materials or hot gases.
TYPE BI
centrifugal ventilating fans
FOR CLEAN AIR APPLICATIONS THRU AMCA CLASS 2 PERFORMANCE
non-overIoading BI meets today’s requirements for ventilating fans with high operating efficiency, quiet operation, versatility of application, rugged construction and built-in ease of maintenance. Arrangement 1, sizes GOO thru 1200 are available in single inlet, single width AMCA Classes 1 and 2, clockwise and counterclockwise rotations and top horizontal and upblast discharges. These fans are designed for belt drive or direct drive through a flexible coupling. The BI is complete with a heavy gauge welded steel housing; torusoidal inlet bell with fixed guide vanes; wheel with single thickness, backwardly-curved airfoil blades and a rugged bearing base. AMCA Class 1 fans are furnished
TYPE BI
centrifugal ventilating fans
FOR CLEAN AIR APPLICATIONS THRU AMCA CLASS 2 PERFORMANCE
non-overIoading BI meets today’s requirements for ventilating fans with high operating efficiency, quiet operation, versatility of application, rugged construction and built-in ease of maintenance. Arrangement 1, sizes GOO thru 1200 are available in single inlet, single width AMCA Classes 1 and 2, clockwise and counterclockwise rotations and top horizontal and upblast discharges. These fans are designed for belt drive or direct drive through a flexible coupling. The BI is complete with a heavy gauge welded steel housing; torusoidal inlet bell with fixed guide vanes; wheel with single thickness, backwardly-curved airfoil blades and a rugged bearing base. AMCA Class 1 fans are furnished
with deep groove ball bearings on sizes 600 thru 980, roller bearings on size 1085 and split pillow block roller bearings on size 1200. AMCA Class 2 fans are furnished with deep groove ball bearings on sizes 600 thru 730, roller bearings on sizes 805 thru 980 and split pillow block roller bearings on sizes 1085 thru 1200. The shaft extends beyond the bearing base and has a keyway for installation of the user’s sheave or coupling. All units are statically and draamically balanced before shipment. Arrangement 1 BI fans are available with optional unistmt motor rails shipped loose with the fan. The unistrut rails can be shipped loose for permanent mounting to the BI fan bearing base by the fan user.
“PB” & “RPB”
centrifugal ventilating fans
PERFORMANCE DATA
size | max cfm | sp* range |
2vpbh | 149 | to 2" |
2pb | 200 | to 3" |
3pb | 387 | to 5 1/2" |
4pb | 544 | to 6" |
4.5pb | 700 | to 11.1" |
5pb | 1500 | to 23.7" |
5.5pb | 2800 | to 33.0" |
6pb | 3400 | to 35.0" |
7pb | 8000 | to 59.1" |
2rpb | 300 | to 19.9" |
3rpb | 800 | to 30.5" |
4rpb | 2000 | to 48.3" |
ACCESSORIES
- Drain
- Shaft Seal
- Inlet Screen
- SPB Bearings Arrangment 1
- 600*F Construction
- Flange Inlet
- Flange Outlet
- Paddle Wheel 2RPB
- Double Flange Wheel (3RPB & 4RPB)
- Flange / Back Plate Wheel (4RE-7RE)
ROTATION AND DISCHARGE AVAILABILITY
fan | fabricated steel | cast iron |
2veh | ccw/bh | - |
2e | ccw/bh | cw or ccw* |
3e-7e | cw or ccw* | cw or ccw* |
2re-4re | cw or ccw* | ccw* |
* Discharge available in any 45* increment
DIRECT-CONNECTED, CAST IRON HOUSINGS
Baby Vent Sets
40 TO 1800 CFM
ACCESSORIES
HOUSING DRAIN
A 1/2″ drilled and tapped hole at the lowest point of the fan scroll to facilitate condensate drainage is available.
INLET/OUTLET SCREENS
Factory mounted hot dipped galvanized steel inlet and outlet screens are available.
HEATSUNGER
Heat slingers reduce heat conduction to the motor bearings which allows higher temperature fan operation. Heat slingers are available on sizes B thru G only.
Canada Blower ‘Baby Vent Sets” are available in seven handle any low pressure intake or exhaust application requiring 40 to 1800 CFM, All sizes are constructed with “rugged” cast iron housings, making them ideal for corrosive exhaust. Forward curved wheels are available in aluminum (sizes A-G) or steel (sizes B-G) and are direct connected to the motor shaft. All sizes are available in both clockwise (CW) and counterclockwise (CW) rotation.
Discharges can be furnished in any 45° incre-ment. All motors are ball bearing totally enclosed. Both fan cooled (TEFC) and explosion proof (TEXP) are available depending on your particular need. Motors %HP and smaller are either 1/60/115 or 1/60/115-230 while motors %HP and larger are 3/60/230-460. Aljjacis^re statically and dynamically balanced by Canada Blower prior to shipment.
THE FOLLOWING ARE AVAILABLE WITH EXTENDED DELIVERY:
Motor Weather Covers, Vibration Isolators, Stainless Steel Wheels, and Special Coatings
including Bisonite M, Phenoflex 8957, and Heresite Baked Phenolic.
DIRECT-CONNECTED, CAST IRON HOUSINGS
Baby Vent Sets
40 TO 1800 CFM
ACCESSORIES
HOUSING DRAIN
A 1/2″ drilled and tapped hole at the lowest point of the fan scroll to facilitate condensate drainage is available.
INLET/OUTLET SCREENS
Factory mounted hot dipped galvanized steel inlet and outlet screens are available.
HEATSUNGER
Heat slingers reduce heat conduction to the motor bearings which allows higher temperature fan operation. Heat slingers are available on sizes B thru G only.
Canada Blower “Baby Vent Sets” are available in seven sizes to handle any low pressure intake or exhaust application requiring 40 to 1800 CFM. All sizes are constructed with “rugged” cast iron housings, making them ideal for corrosive exhaust. Forward curved wheels are available in aluminum (sizes A-G) or steel (sizes B-G) and are direct connected to the motor shaft. All sizes are available in both clockwise (CW) and counterclockwise (CW) rotation.
Discharges can be furnished in any 45° increment. All motors are ball bearing totally enclosed. Both fan cooled (TEFC) and explosion proof (TEXP) are available depending on your particular need. Motors 3/4HP and smaller are either 1/60/115 or 1/60/115-230 while motors 3/4HP and larger are 3/60/230-460. All fans are statically and dynamically balanced by Canada Blower prior to shipment.
THE FOLLOWING ARE AVAILABLE WITH EXTENDED DELIVERY:
Motor Weather Covers, Vibration Isolators, Stainless Steel Wheels, and Special Coatings
including Bisonite M, Phenoflex #957, and Heresite Baked Phenolic.
fan with high operating efficiency, versatility of application, rugged constmctionand built-in ease of maintenance. Canada Blower engineers designed Canada Blower Exhauster with these criteria in mind. This line of industrial quality fans offers the ideal solution to the air moving problems of modern industry and represents the result of over 100 years’ experience and engineering leadership in the design and manufacture of air handling equipment.
INDUSTRIAL EXHAUSTERS
ARRANGEMENTS 1 & 9
SIZES: 17-80
CAPACITY: 270 CFM to 35,750 CFM
PRESSURE: Static Pressures to 20” W.G.
STANDARD CONSTRUCTION ARRANGEMENT 1 FAN
AVAILABLE WHEEL TYPES
MW – SIZES 17-80
GRANULAR MATERIALS
The radial bladed MW wheel is
designed for smooth air flow performance and optimum operating
efficiency; The MW wheel is ruggedly built to handle clean air,
corrosive fume removal or air-fume
mixtures containing granular materials such as grains, dust or abrasive exhaust from grinding or ” buffing operations.
OW – SIZES 17-80
FIBROUS MATERIALS
The radial bladed OW cone wheel is fabricated with no front flange. Omission of the flange allows free passage of fibrous materials such as wood shavings, ensilage, paper strips, textile products and other materials which normally tend to clog flanged type wheels.
AW – SIZES 17-80
HOT GASES
The AW wheel is designed for maximum efficiency while handling hot air, gases, fumes – either clean or containing light concentrations of solid materials. The backwardly inclined blades are curved slightly to maintain efficient gas flow through the fan.
MODIFICATIONS AND ACCESSORIES
Arrangement 9 Construction
Split Pillow Block Roller Bearings
Oversized Shaft and Bearings
Type “C” Spark Resistant Construction
Housing Access Door
Housing Drain
Flanged Inlet & Outlet
Thermosil Shaft Seal
Heat Slinger
OSHA Inlet Screen
OSHA Shaft Guard
OSHA Belt Guard
Unistrut Motor Rails
Modifications and accessories are available on all sizes to meet your demanding industrial and processing needs.
OPTIONAL ARRANGEMENT 9 FAN WITH VARIOUS ACCESSORIES AND FACTORY MOUNTED MOTOR AND V-BELT DRIVE
WHEELS
The flanged wheel is built of all riveted construction with two die-formed rims and five die-formed radial blades of heavy gauge steel and a cast steel spider.
HOUSING
The fan housing, shown, is a one piece grey iron casting. The housing inlet plate and drive side plate are also one piece grey iron castings, bolted to the housing. The fan inlet and outlet are designed for slip connection to the user’s duct or standard size pipe.
BEARINGS
Arrangement 1 Volume Fans are equipped with two heavy duty, single row, deep groove grease lubricated ball bearing pillow blocks mounted on a rugged fabricated steel bearing base. The shaft is ground and polished steel with a keyway for installation of the user’s sheave or flexible coupling.
FOR ABRASIVE AND CORROSIVE APPLICATIONS
Canada Blower Volume Fans provide extended service life and reliable performance in punishing applications. A ruggedly contructed cast iron housing and heavy gauge fabricated steel wheel and housing supports enable the Volume Fan to provide long, troublefree service in applications handling hard, gritty, abrasive material in the air stream. Because all housing parts, which come in contact with a contaminated air stream,
are constructed of cast iron, the Volume Fan can be successfully used in applications with corrosive vapors present. These fans are particularly adaptable to pneumatic conveying, drying, supplying combustion air, exhausting waste air, gas, vapor and/or materials, ventilating and inflating. The pressure and volume characteristics are more than adequate to handle the requirements usually encountered in this type of work.